|
SPECIAL PRODUCTS |
MECHANICAL TIME & IMPACT FUZE (FOR ARTILLERY GUNS & MORTARS)
IMPACT FUZES ( FOR MORTARS )
IMPACT & SELF DESTRUCTION FUZES (AIR DEFENCE FUZES)
OTHER FUZES FOR 84 mm AMMUNITION
POINT DETONATING FUZES
POINT INITIATING & BASE DETONATING FUZE
AIR BOMB FUZES
IMPACT FUZES (FOR ROCKET)
SAFETY & ARMING DEVICES
SAFETY ACTUATING MECHANISM FOR MISSILES
ELECTRONIC TIME FUZES FOR ROCKETS
PRIMERS
ELECTRONIC DETONATING DEVICE
CRUSHER GAUGES FOR MEASURING THE GAS PRESSURE IN THE GUNS
Ψ MECHANICAL TIME & IMPACT FUZE (FOR ARTILLERY GUNS & MORTARS)
Fuze Time & Percission DA 213 MK5 (M-1) & (M-2)
USAGE SPECIFICATION
|
Compatible to Guns & HOWITZERS From 75mm to 183mm Calibres. M-1 is used with high explosive shells while M-2 is used with Smoke and cargo carrying projectiles.
|
|
Fuze Time & Percission DA 213 MK5 (M-3) & (M-4)
USAGE SPECIFICATION
|
|
USAGE SPECIFICATION
|
· Used with high explosives shells of 84mm recoilless anti-tank weapons.
|
40 to 1250 metres at intervals of 10 metres
|
Ψ IMPACT FUZES (FOR MORTARS)
Fuze 162 MK 8(M-2) & MK9 (M-1)
USAGE SPECIFICATION
|
|
USAGE SPECIFICATION
|
· Used with high explosive and WP Smoke bombs of both 81mm & 120mm Calibre mortars
|
|
USAGE SPECIFICATION
|
· A direct action detonating type of fuze for mortar bombs. Used with 2 inch / 51 mm mortars HE ammunition
|
|
Ψ IMPACT & SELF DESTRUCTION FUZES (AIR DEFENCE FUZES)
USAGE SPECIFICATION
|
|
USAGE SPECIFICATION
.
|
|
USAGE SPECIFICATION
|
|
USAGE SPECIFICATION
|
--------
|
Ψ OTHER FUZES FOR 84 mm AMMUNITION
FUZE M541 FOR 84 mm SMOKE SHELL
USAGE SPECIFICATION
|
· Arming Condition : o Minimum time to Arm : 0.15 sec o Non-arming distance : Upto 20 m o Arming distance after 70 m o The impact mechanism functions down to an angle of impact of 5 degree.
|
USAGE SPECIFICATION
|
· Illuminating area (Dia) : 400 to 500 meter. · Firing Range : 600 m, 1100 m & 1700 m. · MUZZLE velocity : 260 m / sec.
|
IMPACT FUZE FOR INCENDIARY AMMUNITION
USAGE SPECIFICATION
|
· Used for direct ignition of shell on impact |
· Arming Condition o Minimum time to Arm 0.15 sec o Non arming distance : Upto 20 m. o Arming Distance after 70 m
|
Ψ POINT DETONATING FUZES
USAGE SPECIFICATION
|
· Used with High Explosive shells of artillery guns of 75 mm to 203 mm caliber. · Offers choice of Instantaneous or Delayed action. |
· Arming Condition : o Minimum Spin : 2000 rpm · Operating Modes : o Instantaneous Delay : 0.05 sec
|
POINT DETONATING FUZE PDM 572 C1
USAGE SPECIFICATION
|
· Arming Condition. : o Spin : 2000 rpm o Distance : 200 ft o Acceleration : 1000 g · Operating Mode : o Instantaneous o Delay : 0.05 sec. |
Ψ POINT INITIATING & BASE DETONATING FUZE
USAGE SPECIFICATION
|
Used with Heat Shells of 125mm Gun. A high Precisions, sensitive fuze which enables instant destruction of heaviest known tanks.
|
|
USAGE SPECIFICATION
|
It is a Point Initiating Base Detonating Fuze A Piezoelectric crystal in the Nose of the shell generates electrical Impluse to fire the Detonator Used with Heat Shells of 105mm Tank Guns and 106mm recoilless guns
|
|
Ψ AIR BOMB FUZES
FUZE BALLASTIC TAIL NO FBT-3I & NOSE FUZES FBN 21 & FBRN 41
USAGE SPECIFICATION
|
--------------------- |
SAFETY ARMING FUNCTIONING UNIT FOR CLUSTER BOMBS
USAGE SPECIFICATION
|
· Arming Conditions: o Arming Delay : 0.68, 0.8,1.0 or 1.2 secs. o Spin Required : Minimum : 1800 rpm Maximum : 2200 rpm o Air Speed : 140 metres per sec. · Operating Modes : o Mechincal Time Device
|
TIMER & PROBE ASSY FOR CLUSTER BOMBS
USAGE SPECIFICATION
|
· Arming Conditions. o Present Arming o Delay : 0.7 seconds o Environmental sensing to ensure arming at specified speed. · Operating Mode : · Point Initiating Base Detonating
|
FUZING COMPONENTS FOR AIR BOMB
USAGE SPECIFICATION
. |
---
|
Ψ IMPACT FUZE (FOR ROCKET)
FUZE DA & DELAY FOR 122 mm ROCKET
USAGE SPECIFICATION
. . |
· Arming Conditions o Acceleration required : 30 to 35 g o Arming distance : 150 to 400 metres · Operating Modes o Instantaneous o Delayed action |
USAGE SPECIFICATION
|
· Used with High Explosive shell 140 mm.
|
· Arming Conditions o Arming Distance : 500 meters · Operating Modes o Direct Action o Graze Action
|
HOLLOW CHARGE FUZE FOR 68 mm ROCKET
USAGE SPECIFICATION
|
· Used with 68 mm Heat Rockets. Enables swift, superior and accurate fire power against tanks by use of Rockets fired from aircraft. . . |
· Arming Conditions o Non-Arming Acceleration: 30 g o Arming Acceleration : 60 g · Operating Modes o Base Fuze : Electrically Fired · Delay : 400 to 550 milli seconds.
|
TIME & PERCUSSION DA FUZE 213 MK 5 (M.R.) FOR MRECM ROCKET
USAGE SPECIFICATION
. |
· Arming condition: o Non Arming : 15 g o Arming : 25 g · Operating Modes · Time Function : Setting upto 120 sec at intervals of 0.5 sec. |
Ψ SAFETY AND ARMING DEVICES
USAGE SPECIFICATION
|
· Arming condition : o An arming delay mechanism provide for trajectory safety. o Requires a minimum of 200 ft of projectile travel to reach the armed position |
USAGE SPECIFICATION
|
· Arming condition o An arming delay mechanism provide for trajectory safety. An additional safety is given by a set back pin. o Requires a minimum of 200 ft of projectile travel to reach the armed position |
SAFETY & ARMING DEVICE FOR PROXIMITY FUZES 105 & 130 MM
USAGE SPECIFICATION
|
· Used with VT Fuzes of artillery guns and howitzers from 75 mm to 130 mm calibers. |
· Arming condition o Minimum spin required : 4500 RPM o Minimum time to arm : 255 milli sec. o Minimum Arming distance : 80 metres. o Positive arming at : 370 metres.
|
SAFETY DELAY ARMING MECHANISM FOR 76.2 mm NAVAL GUNS FUZES
USAGE SPECIFICATION
|
· Used with VT Fuzes of artillery guns and howitzers from 75 mm to 130 mm calibers. |
· Arming condition o Minimum spin required : 4500 RPM o Minimum time to arm : 255 milli sec. o Minimum Arming distance : 80 metres. o Positive arming at : 370 metres.
|
ARMING DELAY DEVICE FOR PROXIMITY FUZES
USAGE SPECIFICATION
|
· Arming condition o An arming delay mechanism provide for trajectory safety. An additional safety is given by a set back pin. o Requires a minimum of 200 ft of projectile travel to reach the armed position .
|
SAFETY & DELAY DEVICE FOR FUZE FFV 651
USAGE SPECIFICATION
|
· Arming condition o Arming distance : 5 to 15 metres o Arming Delay: Minimum : 45 millisecs Maximum : 65 millisecs.
|
SAFETY LOCK ASSEMBLY FOR SELF DETONATING FUZES
USAGE SPECIFICATION
|
· Arming condition o Non arming : 30,000 RPM o Arming : 55,000 RPM
|
SAFETY arming & Delay Device for L 29 A3 FUZE
USAGE SPECIFICATION
|
· A mechanical safety, arming and delay device used in base detonating fuzes
|
· Arming condition o Minimum Spin required : 7000 rpm o Arming Delay : 9 to 19 milli-sec. o Minimum Arming distance : 3.658 metres. o Positive arming : 30.5 metres
|
Ψ SAFETY ACTUATING MECHANISM FOR MISSILES
SAFETY ACTUATING MECHANISM FOR MISSILES
USAGE SPECIFICATION
|
· Arming condition o Acceleration : Non arming at 9 g o Arming at: 13 g o Arming Delay : Minimum : 1.5 seconds Maximum Time : 48 secs of Timer Unit. o Self Destruction : Acts after 25 secs (of Surface to-Air Missile.)
|
Ψ ELECTRONIC TIME FUZE FOR ROCKETS
ELECTRONIC TIME FUZES FOR ROCKETS
USAGE SPECIFICATION
|
· Time Setting : From 6 secs to 256 secs in steps of 0.1 sec by use of snap-off connector.
|
PRIMERS
Ψ ELECTRONIC DETONATING DEVICE
SPARK ELECTRIC DETONATOR (S.E.D.)
USAGE SPECIFICATION
|
· Used in FUZE B-15 for 125 mm HEAT AMN
|
· The SED generates a spark which initiates Lead Azide which in turn detonates PETN (Filled in SED) which passes detonation wave to Lead Charge & then Detonator. · Electrical Test : No spark at 700/900 V. Spark at 1500 / 1800 V.
|
USAGE SPECIFICATION
|
· Used for operating Fire extinguisher for air craft
|
· Operating Mode o The cartridge is fired by application of 24 volt DC
|
ELECTRICAL PROPELLING CHARGE IGNITER
COMPLETE ELECTRIC SYSTEM FOR FUZE FFV 651
USAGE SPECIFICATION
|
· Used in 84 mm Heat FFV 651 · The electric system consists of a piezoelectric crystal with leakage resistor, a diode with leakage resistor & insulating tubes for the leads.
|
(One micron A) at 150 V .
o Temp range : +60 degree Centigrade to 40 degree centigrade. |
Ψ CRUSHER GAUGES FOR MEASURING THE GAS PRESSURE IN THE GUNS.
CRUSHER GAUGES FOR MEASURING THE GAS PRESSURE IN THE
USAGE SPECIFICATION
|
· Used for measuring the gas pressure in Guns.
|
· MK-9 Pressure 155 to 660 MPa |